No Service after JB

**janzy** · 04-04-2011, 01:00 PM

Just used the latest version to Jailbreak my IPhone 4 and everything but the phone itself works.
says I have no service.
Any ideas
Thanks

**Simon** · 04-04-2011, 01:10 PM

If you used pwnage tool and are on official carrier you need to make sure you do not choose to activate with pwnage tool or you will get no signal.

**janzy** · 04-04-2011, 01:17 PM

I am on an official carrier.
How do I correct the issue, I'm a newbie.
Thanks

**Simon** · 04-04-2011, 01:20 PM

Make the custom firmware again, this time near the end of the process click on general and deselect the box that says to activate. Use expert mode.

**janzy** · 04-04-2011, 01:24 PM

Thank you, I'll give it a shot when I get home from work.

**Simon** · 04-04-2011, 01:26 PM

no prob, good luck

**nhoj_yelbom** · 04-04-2011, 03:40 PM

if you are preserving your baseband only expect 1 bar and it does not move, it is a problem with older bb on 4.3.1 and they are working on it

**FinalBillybong** · 04-04-2011, 04:21 PM

Originally Posted by nhoj_yelbom

if you are preserving your baseband only expect 1 bar and it does not move, it is a problem with older bb on 4.3.1 and they are working on it

Ok so I am on official carrier but preserved baseband and only have 1bar of signal. Is this a problem with the phone displaying the wrong thing or do I actually have low signal? I assume installing the latest version of Ultrasn0w (when it's released) will solve the issue?

**Simon** · 04-04-2011, 04:26 PM

Originally Posted by FinalBillybong

Ok so I am on official carrier but preserved baseband and only have 1bar of signal. Is this a problem with the phone displaying the wrong thing or do I actually have low signal? I assume installing the latest version of Ultrasn0w (when it's released) will solve the issue?

It's just a bug with how the signal is displayed.

**kangorillas** · 04-04-2011, 04:58 PM

Originally Posted by x98car

It's just a bug with how the signal is displayed.

it's no display bug I get no service connectivity either.

**FinalBillybong** · 04-04-2011, 05:00 PM

If you get no service it's because you has activate iPhone ticked in Pwnage Tool.

I get service but it's always 1 bar.

**Simon** · 04-04-2011, 05:00 PM

Originally Posted by kangorillas

it's no display bug I get no service connectivity either.

If you are getting no service then you have a different issue.

**Simon** · 04-04-2011, 05:00 PM

Originally Posted by FinalBillybong

If you get no service it's because you has activate iPhone ticked in Pwnage Tool.

I get service but it's always 1 bar.

Exactly.

**Beezure** · 04-04-2011, 05:03 PM

i have the same problem, using redsnow, tried twice, cell not working (att), but jb is (cydia wireless) iphone 4

**Simon** · 04-04-2011, 05:19 PM

Originally Posted by Beezure

i have the same problem, using redsnow, tried twice, cell not working (att), but jb is (cydia wireless) iphone 4

Restore again. This time make sure the phone is activated before running redsnow

**Beezure** · 04-04-2011, 05:48 PM

Originally Posted by x98car

Restore again. This time make sure the phone is activated before running redsnow

thanks, did the trick

**Simon** · 04-04-2011, 05:50 PM

no prob

**gruv2ths** · 04-05-2011, 09:25 PM

Same problem here, IPSW installs but i get no connection to ATT once installed.

Where exactly in the pwnage do you see the activate option? Is it after you build the file or before?
Someone said in General, where is that?
BTW the base band is: 4.10.1

Any help would be great!! Thanks!!

**janzy** · 04-06-2011, 04:13 AM

On the build page go to general and unclick "activate phone" and you're good to go.

Thread: No Service after JB

LinkBack

Thread Tools

Display