+ Reply
Results 1 to 4 of 4

Your favorite Apple, iPhone, iPad, iOS, Jailbreak, and Cydia site.


Thread: iPod Touch 4th Generation Written Screen Repair Guide

is a discussion within the

iPod Service, Warranties, and Repairs

forums, a part of the

General iPod

section;
Is the screen assembly on your iPod Touch 4th Gen not functioning correctly? Are other internal parts such as the headphone jack, battery, etc. in need of replacement? Are you
...
  1. #1
    What's Jailbreak?
    Join Date
    Mar 2012
    Posts
    12
    Thanks
    0
    Thanked 5 Times in 3 Posts

    Post iPod Touch 4th Generation Written Screen Repair Guide
    Is the screen assembly on your iPod Touch 4th Gen not functioning correctly? Are other internal parts such as the headphone jack, battery, etc. in need of replacement? Are you just curious how to disassemble your iTouch 4th Gen to see what makes it tick? This written guide will walk you through all the steps required to safely and quickly disassemble your device and make repairs, most specifically the screen assembly.
    The iPod Touch 4th Gen uses a screen assembly which is fused together, making replacing a single screen very difficult without damaging the others. If performing a screen repair, we highly suggest using a full screen assembly to avoid further damage.

    This guide will help you install the following iPod Touch 4th Generation parts:
    • iPod Touch 4th Generation LCD & Touch Screen Digitizer Replacement
    • iPod Touch 4th Generation Battery
    • iPod Touch 4th Generation Home Button
    • All Other Internal Flex Cables, Speakers, Housing, and Parts

    Tools Required:
    • Open Safe Pry Tool
    • Small Phillips Screwdriver
    • Hot Air Gun/Hair Dryer

    iPod Touch 4th Gen Screen Repair Take Apart Guide:
    • To begin taking apart your iPod Touch 4th Generation, you will first need to use a hair dryer or hot air gun to heat up the adhesive that is holding the touch screen digitizer in place. Apply the hot air all around the edges.
    • Once the adhesive has been warmed, you will need to use your open safe pry tool to begin separating the glass screen from the rest of the iPod Touch 4th Gen. Using your open safe pry tool, gently slide it between the glass and the chrome, prying slightly as you go around the edges, as shown in Figure 1.


    iPod Touch 4th Generation Written Screen Repair Guide-touch-4th-fig1.jpg
    Figure 1

    • There are clips between the glass and the backing two that will need to be pried and released as you go. As you go, you may need to work the open safe pry tool gently back and forth to separate the two.
    • Once you have disconnected the glass all the way around, you will want to lift the glass up from the bottom gently, as there is still a ribbon cable attached at the top. The image in figure 2 shows how to raise the glass properly without damaging the ribbon cable.


    iPod Touch 4th Generation Written Screen Repair Guide-touch-4th-fig2.jpg
    Figure 2

    • You will now be able to disconnect the ribbon cable on the right side, but it will still be connected on the left. Gently place the glass on the table above the base, leaving this ribbon cable connected for now.
    • You will now need to remove the eight small Phillips screws using your small screwdriver. They are located around the edges as shown in Figure 3.


    iPod Touch 4th Generation Written Screen Repair Guide-touch-4th-fig3.jpg
    Figure 3

    • You will need to separate the midsection of the iPod 4th Gen. by gently prying up where you removed the screws. Figure 4 shows how to do this.


    iPod Touch 4th Generation Written Screen Repair Guide-touch-4th-fig4.jpg
    Figure 4

    • Using a small Phillips screwdriver, remove the screw that is holding the mother board in place. Then you can gently raise the mother board up using the open safe pry tool and your fingers.
    • With the mother board removed, you will be able to easily pop off the ribbon cable that is still attached. After doing this, being careful to not damage the cable, the back of the iPod can be separated from the screen.
    • Now you will be able to install your new touch screen digitizer by reversing the steps taken, but using your new part to achieve an almost new iPod Touch 4th Generation.

    The iPod Touch 4th Generation is now disassembled and you can replace the damaged part(s) with new ones. Reverse the instructions above to reassemble your phone.

    NOTE: This guide was approved by Kyle Matthews.
    Last edited by repairs universe; 03-22-2012 at 01:59 PM.
    Paul Weatherley
    Repair Technician

  2. #2
    Owner / Founder - ModMyi
    aka poetic_folly
    Kyle Matthews's Avatar
    Join Date
    May 2007
    Location
    Tampa, Florida, United States
    Posts
    8,458
    Thanks
    562
    Thanked 4,750 Times in 1,210 Posts

    (yes, approved by me, as well as the sig link). thanks, looks good!
    .


    ↑ ↑ ↓ ↓ ← → ← → B A [select] [start] Kyle Matthews

  3. #3
    What's Jailbreak?
    Join Date
    Jun 2012
    Posts
    1
    Thanks
    0
    Thanked 0 Times in 0 Posts

    This repair tutorial is inaccurate and missing several steps. For one thing there are no clips holding the screen on the 4th gen, it is held by adhesive tape all the way around with the exception of a small bracket at the top right that is stuck to the digitizer and goes around the camera and the light sensor.

    This tutorial will likely result in damage to users ipods. I repair and sell ipods, the screen repair is the most common and this tutorial is far from accurate or complete.

  4. #4
    H4CK3R's Avatar
    Join Date
    Jan 2012
    Location
    java.lang.IllegalStateException: Location unknown.
    Posts
    5,781
    Thanks
    61
    Thanked 261 Times in 250 Posts

    Try contacting the OP or use the Contact Us page. That'd be your best bet.
    Great minds discuss ideas.
    Average minds discuss events.
    Small minds discuss people.

Posting Permissions
  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts